HOLGA FILM LOADING INSTRUCTIONS

Bravely I opened it up and rewinded it, I guess it didn’t roll over the spool properly the first time, and I was too afraid at first to open up and check. Perhaps time to change film..? Yea, thank you everyone for their great advice. Maybe right this film off as a test at loading? Four colors – blue, red, orange and grey are available for selection. If you have wound for 3 mins and nothing has shown up, its likely you havent got the film caught on the take up spool. Although this camera is basically a fixed focus camera, it still offers four choices of object distances. Was hoping to get some help from some experts out there!

There are four symbols on the focus ring to select the following object distances -. There were no instructions to remove the black backing from the film, therefore I am assuming to leave it. Then it’ll still be upside down, won’t it? The effects of putting color filters over the built-In flash when using the flash function are similar to those of putting color filters over the lens without the use of flash. There is all you need to know and more about using a Holga. Now I see the number, but have a suspicion that the film is too over exposed now..

More precise setting for object distances can be achieved by setting the focus ring at positions in between two symbols. Thank you in advance! There are the letters W, R, B and Y engraved around the edge on the top surface of the dial.

(Help!) Loading Film into Holga GCFN Camera | Holga | Flickr

Please refer to paragraph Four colors – blue, red, orange and grey are available for selection. If you have wound for 3 mins and nothing has shown up, its likely you havent got the film caught on the take up spool.

Lorenzo, that is exactly what I am thinking, the black backing must make it quite difficult to see, it even did the winding by the window and glared into it, and didn’t see any movement. They stand for the following. The steps to be taken are as follows.

  VALAKI TUD VALAMI JO HORROR FILMET

Hey guys, i know this is really late but i have exactly the same problem! I had thought I had been carefully following the instructions.

Follow the steps below to set the frame instguctions and frame number. There is the number “16” or “12” in one of the corners of the frame size masks for identification.

These lense have a clear circular olading in the middle and the remaining areas frosted, They are for standing out the object to be taken to make the theme of the picture more prominent. I thought it was funny. There were no instructions to remove the black backing from the film, therefore I am assuming to leave it. To lower the color temperature to remove filn cold tone in flash light to accomplish a warmer light source.

SERIES MEDIUM FORMAT CAMERAS OPERATION INSTRUCTIONS – HOLGA

The worst that cna happen is that you will ruin the film and have to load anew one. I love Flickr for the reason that people are always so helpful and encouraging! There are three filters, namely red, blue and yellow available for changing the color temperature of the originally K white daylight emitted by the flash.

There is the flash color filter selection dial on the top of the camera. Yea, thank you everyone for their great advice.

Have you seen the Squarefrog page? The effects of putting color filters over the built-In flash when using the flash function are similar to those of putting color filters over the lens without the use of flash.

If it’s wound onto the take up spool and you’ve missed the numbers as you wound the film on and then you have wound it back onto the original spool then chances are you have knackered the film.

  LEGENDA SARPELUI ALB FILM

120 SERIES MEDIUM FORMAT CAMERAS OPERATION INSTRUCTIONS

Although this camera is basically a fixed focus camera, it still offers four choices of object distances. I was hoping if someone would have an idea why this may be? I’ve used GP3 in my holga with great results, careful looking when winding on is all that is needed, and only shoot it in bright sunlight.

As the film is advanced manually, this camera can help achieve special effects through multiple exposure by not advancing the film after a frame has been exposed.

To reduce the instructiions of blue light to correct the sensitivity of full color films to lights in the blue to purple range. Color filters are for altering the color temperatures of the object and the background to enhance the artistic effect of the picture. To raise the color temperature e.

As long you scan with the shiny side down it doesn’t matter what orientation the neg is in as you can to adjust it in your editing software afterwards.

Hey guys, I just gave it another go. Thank you for everybody for their helps and tips, I will try each and one of them tonight!

Overview Discussions Photos Members Map.

Yes, leave the backing on. Well, if the numbers on the back of the film are upside down Each depression of the shutter release instrictions will bring about another exposure. With little knowledge, I went to the camera shop, and the guy told me that these Lomography film were made for cameras like the Holga I had. I have been so excited about putting it to use!